Peugeot 208 Key Replacement
Peugeot 208 key replacement should be left to professional auto locksmiths with the right equipment and technical knowledge. They will be able to make and program new keys much quicker than a dealership and at a lower cost.
A dead battery for your coin is most likely to be the cause the reason your key-fob stops locking or unlocking doors. There are other possibilities that the key is malfunctioning.
Dead Coin Battery
A dead battery in the coin compartment will stop your Peugeot 208 from locking or unlocking, and cannot start the engine. If this is the scenario, you'll need utilize the backup starting method that is detailed in the owner's manual for your vehicle.
The spark plugs could also be worn out. The spark plugs are responsible for instigating the fuel that ignites the engine. However, they have a limited time of life. If they aren't used enough to last, they'll eventually fail.
Luckily, there's an easy solution to this issue. The best solution is to test the voltage of your car battery using a multimeter. If the voltage is less than 11,5 volts, then it's time to replace it. If the battery has corrosion it is essential to clean its contacts. You can do this by lifting the rubber covers covering both battery terminals and using wire brushes to clean any parts that are corroded from the battery. Then, reconnect the positive and negative pole cables.
Water Damage
If your 208 isn't starting and the battery isn't flat then you should check whether the spark plugs work. It is possible that they are overly filthy, making them unable to spark. This is easily fixed by cleaning the spark plugs in the workshop.
Peugeot cars have a transponder key that is compatible with the car's immobiliser system. This ensures that only a valid key can turn the engine. If the chip inside the Peugeot key is damaged, then it will not send the correct signal to the vehicle.
This is a frequent issue that is caused by water damage. www.g28carkeys.co.uk is a common problem in colder climates where the vehicle is exposed to snow or rain. In this situation, contact a trusted locksmith who has the tools and equipment required to reprogram the key. They also have the most up-to-date technological know-how and the equipment required to make a Peugeot 208 smart key. The process shouldn't be more than 15 minutes.
Contacts of the battery may be damaged.
Peugeot changed from the old carbon encased transponder chips to a brand new type of chip that relies on electronic components in circuit boards. The new system is effective when it's brand new but as time passes, the circuit boards begin to lose their effectiveness and cease working correctly.
This can stop the immobiliser chip from triggering, so your car won't start. If this happens, it's a good idea get in touch with a Peugeot specialist or locksmith.
Another issue that is common is when the battery in the key fob gets depleted, which causes the key blade to stop from entering the lock. A locksmith for cars can replace the battery and cut a new blade for you, it's generally a quick fix.
Faulty Receiver Module
If your Peugeot key fob has stopped working after dropping it on the floor, or being exposed to a sudden downpour or accidentally washing it may be due to a faulty receiver module. The receiver module is responsible for transmitting radio signals to the onboard computer that manages the central locking system of your Peugeot vehicle.
Rubber seals on the key fob stop water from reaching the electronic chip. However, prolonged exposure to water can cause damage to these seals and the chip. The high salt content in the pool or ocean waters can cause damage to the key fob, especially if it is submerged.
The module will need to be replaced if the Peugeot spare key does not work anymore. This can only be done by an expert auto locksmith or Peugeot specialist. Peugeot keys unlike other automobiles, are protected by an immobilizer system. This requires the right programming to allow the car to start. It is for this reason that you should only trust a Peugeot locksmith to design and program a replacement.
Computer with a problem on board
The computer on the board of your Peugeot is the one responsible for all of the systems inside your car, from power windows to airbags. The computer on board will display a code if something goes wrong. The code will be stored in the system until the issue is fixed. This will often require the on-board computers to be replaced.
The most common reason for the warning light of the airbag to illuminate is corrosion or loose connections in the sensor. This can be caused by wear and tear, aging, exposure to salt and moisture. This issue needs to be addressed as soon you can, since an airbag that is malfunctioning could pose danger in the event in the event of an accident.
If you see the error "card not found" on your Peugeot, the key battery inside the key fob might be dead or weak. This will stop the key fob from sending a signal to deactivate the immobilizer on your vehicle. Test this by pressing the unlock button on the fob's key and then trying to start your vehicle. If this fails then the battery in the key fob needs to be replaced.